GearAndRig is reader-supported. As an Amazon Associate I earn from qualifying purchases. When you buy through links on our site, we may earn an affiliate commission, at no extra cost to you. Learn more.
For most RV owners, the Camco Sidewinder 20-foot sewer hose support is the easiest all-around choice: its folding cradles follow a curved hose run and hold the hose without separate tie-downs. Choose the Beech Lane 20-foot support when storage space matters more; choose a Camco sectional or adjustable kit for a curb or awkward elevation. None of these supports can make wastewater flow uphill into a sewer inlet above your RV’s outlet.
A sewer hose support is not a replacement for the hose. It is the rack underneath it. The buying decision comes down to three campsite measurements: how far the drain is from your RV, how high the campground inlet sits, and whether the ground lets you maintain a downhill path without a sag. The four choices below solve different parts of that problem.
The best RV sewer hose supports at a glance
Camco Sidewinder 20 ft (43052)
A flexible accordion with deep hose cradles. Pick it for a conventional full-hookup site where the hose must curve around small obstacles.
Beech Lane 20 ft
Nesting panels and a reversible height arrangement help when your storage compartment is cramped and the site is reasonably predictable.
Camco Rhino Nesting Kit (43072)
Five independent graduated sections for up to 15 feet of standard 3-inch sewer hose, with more freedom to place support where the ground changes.
Camco Adjustable Kit (43071)
Six separate troughs and adjustable legs make this a more deliberate solution when a curb or raised inlet defeats a low accordion.
Compare the designs before choosing
| Support | Manufacturer-stated coverage | What changes the decision | Watch out for | Amazon |
|---|---|---|---|---|
| Camco Sidewinder 43052 | Up to 20 ft of 3-inch hose | One-piece folding run that bends around obstacles; deep, strap-free cradles | The fixed graduated cradle does not independently raise a low sewer end | View |
| Beech Lane 20 ft | 20-ft sewer hose run | Panels nest for reduced storage volume; can be flipped for a different height | Optional stabilizing feet are separate on the standard version | View |
| Camco Rhino 43072 | Up to 15 ft, 3-inch hose | Five independent graduated-height cradles to position along an irregular route | Not intended to support an entire 20-ft run | View |
| Camco Adjustable 43071 | Up to 20 ft | Six independent troughs, stake-adjustable elevation up to 10 inches | Individual troughs are separated; take more time to place and stow | View |
Important sizing distinction: a kit advertised as supporting a 20-foot hose is not necessarily a continuous 20-foot-long plastic trough. The 43071, for example, uses six separate 30-inch troughs distributed along the run. The useful question is whether the unsupported hose between cradles will stay off the ground and free of low spots at your campsite.
Four supports worth choosing for different campsites
Camco Sidewinder 20-Foot Support (43052)
Choose this for a curved, mostly even run when you want one folding support rather than individual parts.
Camco’s current 43052 Sidewinder uses hinged, snap-fit sections that telescope along the hose and bend around a pedestal or other small obstacle. Its cradles are molded deep enough that Camco does not require extra retaining straps. You can compress the entire run for the storage bay instead of collecting separate support pieces.
The limitation is geometry. A one-piece support follows the campsite surface even though its cradles have a graduated profile. A hollow in the ground can still create a low point; a raised campground sewer inlet can still force the hose to rise at the end. Check the actual fall rather than assuming the Sidewinder name guarantees drainage.
Buy it if: your hookup is typically within 20 feet and the ground is roughly level or falls toward the dump inlet. Skip it if: a tall curb, raised inlet, or abrupt change in terrain calls for independently placed or adjustable supports.
Model check: 43052 is Camco’s current 20-foot catalog part. Some Amazon results still show the older 43051 20-foot Sidewinder; both names exist, so confirm the selected listing and 20-foot variant.
Beech Lane 20-Foot Nesting Sewer Hose Support
Choose it when a full-length support needs to fit into a smaller RV storage compartment.
Beech Lane’s design folds the smaller support panels inside the larger ones. This is a more relevant difference than the color or the carrying strap when every inch of pass-through storage matters. The manufacturer also describes a flippable design with two height options. That offers some flexibility, but it is not the same as adjusting six individual legs for a curb.
There is a version-selection trap: the standard 20-foot support and the support sold with clip-on accessory feet are different packages. Beech Lane’s published product description says stabilizing accessory feet are separate for the basic model. If wind or a sideways slope is the reason you are shopping, confirm the exact Amazon variant includes the feet before ordering.
Buy it if: you need 20-foot coverage but your storage bin makes a bulkier folding support annoying. Skip it if: you expect steep, changing elevations and need individually adjustable support heights.
Camco Rhino Nesting Support Kit (43072)
Choose it for a 15-foot-or-shorter run where placing separate supports is more useful than unfolding an accordion.
The Rhino 43072 is a collection of five separate graduated-height supports, not a hinged length of plastic. Camco specifies compatibility with its RhinoFLEX, RhinoEXTREME and Revolution hoses as well as other brands’ standard 3-inch RV sewer hoses up to 15 feet. The manufacturer lists section heights from 8.5 to 10.5 inches. That lets you place the pieces around awkward ground features, but the heights are built in rather than individually adjustable.
This kit is especially worth considering when the sewer inlet is elevated enough that the low end of an accordion would become the problem. Measure first: a 10.5-inch section does not automatically clear a high inlet, and the RV outlet still must remain above it for gravity drainage. The support pieces also need placement that avoids a drooping hose between them.
Buy it if: the typical run is no longer than 15 feet and you need taller, independently positioned cradles. Skip it if: you regularly use the entire 20-foot hose or require genuinely adjustable elevation.
Camco Adjustable Sewer Hose Support Kit (43071)
Choose this when a curb, a raised campground connection, or irregular ground calls for deliberate height adjustment.
Camco’s 43071 provides six trough sections with adjustable legs. The official product description says the cradle can sit approximately 1.75 to 4 inches off the ground without elevated stakes and up to 10 inches with stakes locked in place. The troughs can turn around an obstruction and nest for storage. On concrete, Camco says the supports can work without driving the stakes into the ground.
This is the most configurable option here, but also the one that asks you to pay attention to each section’s height. Gaps between the troughs are normal for its design. A full hose can sag between them if the spacing or grade is wrong. Set up a continuous downhill route and watch the hose while draining instead of treating the published 20-foot coverage as a guarantee against pooling.
Buy it if: the sewer inlet sits higher than most low accordion supports and the RV outlet still provides a workable drop. Skip it if: you only need a simple, quick one-piece rack or the inlet is at or above the RV outlet. An adjustable rack cannot create pressure to lift waste uphill.
Get the length and downhill fall right
Do not choose the support length solely because a sewer kit is sold as 20 feet long. Many RVers carry two 10-foot hose sections but use only one at most campsites. Measure the actual route from your outlet to the inlet with the hose connected in a gentle curve. A support longer than the typical distance can remain partly compressed; a support shorter than the route is acceptable only if the remaining hose does not droop into a trap.
- About 10 feet of hose used: a compact 10-foot accordion can be easier to handle, but a partly compressed 20-footer may be reasonable if you occasionally need the extra reach.
- About 15 feet used: the Rhino 43072 is a plausible sectional choice; a longer Sidewinder or Beech Lane support provides room for a longer future run.
- About 20 feet used: select a support whose stated coverage reaches that distance, then check that the hose remains cradled along its actual curved path.
Check the endpoints first: the RV outlet must be high enough above the campground sewer inlet for gravity to work. Next, look along the entire hose for a belly or uphill segment, especially where it crosses a rut or curb. There is no responsible single slope number to prescribe for every flexible hose and campsite. A continuous fall without trapped low points is the practical goal.
A high sewer inlet changes the answer
A campground sewer pipe may stick several inches above the pad. If the support’s low end is below the pipe opening, the hose has to bend upward just before the connection. That last rise can leave wastewater standing in the hose. Measure the inlet rim, the hose elbow and the RV outlet height before choosing a support, not after you unpack one at the campsite.
For a short run, the Camco Rhino 43072’s taller independent cradles may give you enough clearance. For a more complicated elevation over a curb, the Camco Adjustable 43071 gives you different positions. Neither is a fix when the actual dump inlet is too high for a downhill connection from the RV. In that case, avoid forcing the hose into an uphill loop; ask the campground about another hookup or evaluate a purpose-built macerator system separately.
Small setup errors that defeat an otherwise good support
- Starting from the wrong end: establish where the campground fitting must sit, secure the manufacturer-specified connection, and arrange the cradle heights along the route before releasing waste.
- Stretching an accordion to its limit: a support pulled taut across uneven ground has less freedom to follow a gentle bend or bridge a hollow. Reposition it if the hose starts to sag.
- Ignoring movement: inspect a full, draining hose for a shifted support or a hose that has slipped out of its cradle. A good empty-hose arrangement can behave differently under flow.
- Using a support as a clamp: the rack should cradle the sewer hose, not kink, squeeze or sharply bend it. Use supplied retaining straps only as the manufacturer intends.
- Forgetting campground rules: some sites require sewer hoses to be supported or elevated. Confirm local campground requirements rather than assuming the same rule applies everywhere.
Use appropriate gloves, keep sewer equipment away from drinking-water gear, and follow your RV and hose manufacturers’ tank-emptying instructions. When finished, rinse and dry the support as its manufacturer directs before returning it to its storage compartment.
Which one should you actually order?
Choose the Camco Sidewinder 43052 if you want a straightforward 20-foot support for conventional full-hookup pads. Choose Beech Lane if the same 20-foot reach needs to occupy less storage room. Choose Rhino 43072 for a shorter hose run that benefits from taller, separate sections. Choose Adjustable 43071 when managing several changes in elevation matters more than quick setup. Choose none if the sewer inlet sits above your RV’s outlet or you only connect a short hose during a brief dump and can safely manage its drainage without a rack under local rules.
For an RV sewer support, the best purchase is the one that fits your actual hookup geometry. A support with more features will not cure an uphill pipe, an undersized hose, or a leaking connection.
How these recommendations were selected
This comparison uses current model-specific manufacturer descriptions, the corresponding Amazon.com listings and the practical limits of each support design. The criteria are supported hose length, independent height control, storage arrangement, and whether the design can accommodate a curb or irregular campsite. It is a documented product comparison, not a hands-on durability or drainage test; actual inventory and selected variants can change.
Frequently Asked Questions
Do I need an RV sewer hose support every time I empty the tanks?
Not necessarily. A support is particularly useful for an extended full-hookup connection, a long hose run, or a campground that requires hoses to stay elevated. For a short supervised dump, the essential requirements are a secure connection and a route that drains properly under the RV and hose manufacturers’ instructions. Follow the campground’s rules either way.
Will a 20-foot sewer hose support work with only 10 feet of hose?
Usually a flexible 20-foot support can be used partly compressed rather than stretched to its maximum length. The important check is the actual hose fit and slope after setup. Do not force a stiff or unstable bend merely to use the longer support, and confirm the manufacturer’s sizing information for the selected model.
Can an RV sewer hose support handle a raised campground sewer inlet?
Only if its height and arrangement keep the whole hose draining downhill from the RV outlet into that inlet. Taller separate cradles or an adjustable support may help over a curb or raised connection, but a support cannot move sewage uphill when the campground inlet is above the RV’s outlet.
Are clip-on stabilizer feet included with every Beech Lane support?
No. Beech Lane’s standard nesting 20-foot support and the version bundled with clip-on stabilizing feet are distinct buying options. Check the Amazon listing’s exact package contents if those feet are important for a windy or sloping campsite; do not assume they are included with the base model.
